Fantasy SportsTeam SportsIndividual SportsAnimal SportsThe Olympics

How To Make A Ballet Barre For Home Use

Updated on December 6, 2016

DIY Ballet Barre For Home

If you have ever wanted to create a ballet studio in your own home you will want to install at least one ballet barre. Any aspiring ballerina or the many fans of ballet exercise movements will tell you the many exercises and practices that can be performed with a simple and fairly easy to make ballet barre.

The good news is that with these tips and tricks it is possible to have your very own at-home ballet studio up and running in no time at all.

You will need a few items to get started.

  • A 2 inch wooden dowel
  • Sandpaper
  • A measuring tape
  • A level
  • Ballet Barre Brackets
  • Power drill

Some other items you might need.

  • A stud finder
  • Anchor bolts

Ballet Barre For Home Studio
Ballet Barre For Home Studio | Source

Step 1: Decide where the barre is going to be installed

Choosing which wall will be a personal choice and will most likely be based on how much room you have to spare.

The barre can be as short as two feet or as long as your workout room will allow. There should be enough room to move the leg forward and away from the wall. If you are building this for growing children, you may want to consider future use.

Once you have picked out the best location, it's time to measure.

Step 2: Measure the length the finished barre will be

Have this pre-measured number first. The reason why it’s often easier to have the barre pre-measured is so the hardware store can cut the wooden dowel to the size you need. I found this super handy, one less tool to have to buy or rent.

Tip: Call ahead to the hardware store to make sure they can cut the dowel for you. Almost all of the chain stores offer this feature, but it is best practice to check ahead of your visit.

Ballet Barre Height
Ballet Barre Height | Source

Step 3: The wooden dowel is home

Don't skip this simple, but effective process. Sand the dowel and remove any loose stickers.

I found out that sanding before installing with some inexpensive sandpaper, easily purchased at any local hardware store, was/is a necessary and easy step, often overlooked.

Sometimes additional sanding from time to time is needed as the barre is used, and you may find spots you missed smoothing with the initial sanding.

Tip: A good alternative to a wooden dowel is white PVC piping, it is lightweight, easy to cut, readily available and not too expensive.

Step 4: Measuring the ballet barre height

Measure from the floor up the wall 36 inches. This is the height of the barre. Measure about every foot down the length of your chosen wall.

Tip: If you are building this for a small child, you want the height lowered, maybe 24 inches. Use your best judgement.

Step 5: Measuring for wall brackets

Next you will need to find the studs in the wall. The studs are going to support the brackets, which will support the barre.

Current construction in most areas requires a stud in the wall every 16 inches. One technique is locate an electrical box on the wall. Inside the wall the electrical box is attached to a wooden stud. Tap on the wall on each side of the box and you will notice a hollow sound on the side without a stud. From this point you can measure along the wall 16 inches from where you found the stud holding the electrical box, tap around and see if you can "hear" the next stud. Mark all of the studs with a pencil or pen, along the wall you are going to hang the barre.

How to Locate a Wall Stud For The Brackets

If you can not locate the studs, the next course of action is use a stud finder. Use the stud finders as the manufacturers suggest and mark the studs.

Worst case scenario, there are no studs, you will need to install anchor bolts, first. The anchor bolts will act as studs and hold the dowel in place.

I did not have to do this, but I included this how to video below in case you will need to.

Can't locate the studs? No Problem!

Step 6: Installing the ballet barre brackets

Now that you have located the studs, lay the wooden dowel on the floor below where it will be hanging on the wall.

Find the stud markings , and located the 36 inch high mark also. Take one bracket and grab your level.

Hold the bracket on the 36 inches mark from the floor mark and the stud. Take your level and make sure it is level to the floor. Mark the bracket screw holes with a pencil. This is helpful to mark it, incase you have to leave and come back to the project.

Using your power drill and the screws that came with the brackets. Holding the bracket to your level spot on the wall and drill into the drywall thru the stud. Use caution, to not hit any electrical wiring, stay on the studs.

An alternative to traditional ballet barre brackets are close rod brackets, like the kind that hold up your clothes barre in a closet.

Complete all of the brackets necessary to hold up the barre.

Freestanding Ballet Barre
Freestanding Ballet Barre | Source

Some other alternative options to consider

If you don’t have enough floor or wall space for a barre you may want to consider a freestanding ballet barre.

A freestanding ballet barre are manufactured of aluminum and come in a kit that you put together at home. The base is sturdy and seems to do the trick for single users. This is a great option but if you need even more options, like the ability to move the barre from room to room or studio to studio, there are also portable ballet barres.

Portable ballet barres are shorter, usually about four feet long and the barre is removable. The barre is taken out and then the two legs and barre are transported easily. Because of the shorter size and the collapsing features, it can fit the back of a large car or small pick up.

So there are many options from a do it yourself homemade ballet barre, created with general hardware items, to freestanding barres for those who don’t have the wall space and even a handy portable, collapsible barre for easy transportation.

Are You a DIY'er?

Submit a Comment

No comments yet.